Multi-Stage Pumps
Horizontal and vertical configuration high pressure pumps for water boost applications in both surface and tank mount environments. Stainless steel or cast iron construction with variable suction and discharge orientation. Flows to 350 GPM and 800 feet TDH. Designed to handle a wide range of filtration, pressure boost, wash system and boiler feed applications.
|
| |
| Booster Pumps |
| |
 45HB - 70HB
- Multi-Stage Design: This configuration provides a steady, quiet and vibration-free operation for years of trouble-free service.
- Impellers and Diffusers: Glass filled thermoplastic. Precision molded for high efficiencies.
- Bowls: Constructed with 300 series stainless steel. Rabbet lock for positive alignment - no gaskets required.
- Mechanical Seal: Carbon/ceramic faces. BUNA elastomers 300 series stainless steel metal parts.
- Motor: Close-coupled design. Ball bearings carry all radial/axial thrust loads.
- Designed for continuous operation. All ratings are within working limits of the motor.
- Caution: This is a booster pump. It has no lift capability. DO NOT RUN DRY. DO NOT DEADHEAD.
 Product Bulletin
Instruction Manual
 | top | Back To G & L Pumps
|
| |
 GB Booster Pump Series
- Multi-stage Design: Provides steady, quiet, vibration free, operation.
- Optional Stainless Steel Construction: Standard cast iron for general service or stainless for filtration applications.
- O-ring Casing Seal: Reliable high pressure sealing with easy disassembly for maintenance or repair.
- Impellers and Diffusers: Glass filled engineered composite material with floating impeller design. High resistance to corrosion and abrasion.
- Bowls: 300 stainless steel rabbit lock for positive alignment with no gasket required.
- Variable Capacity: Centrifugal pump design permits selection of flow within a range for each size.
- Mechanical Seal: A variety of face materials and elastomers to match application needs.
- Motors: Close coupled NEMA 56J motors in open drip proof or totally enclosed design. Single phase and three phase available. Ball bearings carry all radial and axial thrust loads. Designed for continuous operation.
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps
|
| |
| Centrifugal Pumps |
| |
 LC
- Close coupled, space saving design provides easy installation.
- Fabricated 304 stainless steel, end suction top discharge, case drain provided as standard.
- Impeller is an enclosed design for higher efficiencies, positively locked on shaft with a key and an impeller nut.
- Mechanical seal has carbon/ceramic faces, 316 series stainless steel metal components and Viton elastomer.
- Optional faces and elastomers available.
- Water circulation Booster services
- Liquid transfer Spraying systems
- General purpose pumping
- Jockey pump service
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
| |
| Horizontal Pumps |
| |
HMS
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
| |
| Vertical Pumps |
| |
DPS
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
| |
 MPVN
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
| |
 SMVT
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
| |
 SSV
- Standard NEMA motors permit a wide variety of options and fast field service.
- NPT threads, ANSI flanges, in-line or top/bottom connections easily fit your piping requirements. The top discharge version may be swung in four directions.
- AISI 304 or 316L stainless steel liquid end components handle more of your pumping needs.
- Seal housing design promotes liquid flow and eliminates entrapped air or heat which could cause premature failure.
- Impeller O-ring seal produces high pressure and efficiency per stage to keep energy costs down.
- Impeller spacing is automatic for quick installation and reduced wear.
- Simplified design for maximum reliability and faster repair.
- Optional horizontal mounting and victaulic connections are available.
Product Bulletin
Instruction Manual
| top | Back To G & L Pumps |
